A Otto's company - serving Sunrise Manor, NV

Genie Torsion Spring Replacement in Sunrise Manor, NV

Raised-panel steelRaised-panel steel
Carriage houseCarriage house
Modern flushModern flush
Full-view glassFull-view glass
LiftMaster openersLiftMaster openers
Chamberlain openersChamberlain openers
Every visit starts with

Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included

We have financing partners for your new garage door*On approved credit; ask us about your options

You get a price before we start. It does not change when the pro arrives.

Get your free estimate

Genie Torsion Spring Replacement: The Sunrise Manor Owner’s Guide

We replace Genie torsion springs in Sunrise Manor every week, and the installed price typically runs $180 to $340 for a single-spring swap and a bit more for a two-spring setup. If your door won’t lift or you heard that jaw-rattling bang from the garage, call (888) 274-8795 and we can often have a truck at your place the same day. Sunrise Manor owners usually find out the hard way: the opener runs but the door doesn’t budge, or one side of the door lifts crooked and hangs there, or there’s a fresh gap in the spring coil where there used to be one continuous spiral.

Call (888) 274-8795

Which Genie Models This Applies To

Genie is one of the most common brands in Sunrise Manor garages, and the torsion springs on those doors are sized to the door’s weight and height, not to the opener. That means a Genie-labeled door from a 1990s tract build can need a different spring than a newer Genie install one street over. The spring’s wire gauge (we see everything from .207 up to .250 on Genie doors around here) and inside diameter have to be matched to the actual door; putting on a spring that’s close enough is how doors get bent.

You’ll find the model and serial on a sticker inside the opener housing or on the door’s hinge side, but the spring itself is matched by the door’s weight and drum size, not the opener model. We measure the door, count the cycles on what’s left of the old spring, and spec the replacement from those numbers. For Genie specifically, the quality aftermarket torsion springs we use meet or beat OEM spec, and we’ll tell you straight whether an OEM Genie spring is worth the wait or if the equivalent gets you back in business faster. We service LiftMaster and Chamberlain doors the same way.

Explore

Styles & brands we work with

  • Raised-panel steel
  • Carriage house
  • Modern flush
  • Full-view glass
  • LiftMaster openers
  • Chamberlain openers

Signs Your Genie Torsion Spring Replacement Is Failing

Springs don’t fail slowly. They give you warnings for weeks, then let go all at once. Here’s what we hear from Sunrise Manor homeowners:

  • A loud bang from the garage. That’s the spring breaking, and it’s usually the first real warning. The door won’t open by hand after it.
  • The opener strains but the door barely moves. The spring was doing the lifting; the opener was doing the guiding. When the spring goes, the opener is suddenly trying to muscle 200 pounds.
  • One side lifts, the other lags. A weakened or broken spring on one side throws the door out of balance, and it hangs crooked on the way up.
  • A visible gap in the coil. A good spring is one continuous spiral. A break shows as a clean separation you can see from the driveway.
  • The door drops fast or slams shut. No spring tension means nothing slows the door on the way down. That’s a safety problem, not just an annoyance.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here in Sunrise Manor, Genie torsion spring replacement runs $180 to $340 installed for a standard single-spring door; two-spring setups push toward the top of that range or slightly above. The price includes the spring, the labor, a balance check, and a safety inspection of cables, drums, and rollers while we’re in there. Cable repair, if it’s needed, runs $130 to $250; roller replacement is $110 to $220.

What drives the number: spring size and wire gauge, single vs. double spring, door height, and whether the cables or drums are also worn. We quote it before we arrive and hold that number at the door, even if the job runs long. Every Genie spring replacement is backed by our 90-Day Done Right Promise in writing. Right now we’re running $40 off any repair over $200, and the Senior & Veteran 10% discount applies always.

DIY or Call Us?

You can safely identify the spring, measure the door’s height, and photograph the model sticker. You can pull the red emergency release cord to disengage the opener and try lifting the door by hand to confirm it’s the spring. That’s the safe list. Replacing the spring is not on it.

A torsion spring holds enough stored energy to break a wrist or worse if it slips during the swap. The tools alone (winding bars, a proper set of them) are not something most homeowners own, and the winding procedure has zero margin for a mistake. We’ve seen the aftermath of a failed DIY spring job more than once, and it’s never worth the savings. Call (888) 274-8795 and we’ll quote it on the call and hold the price.

FAQs

How long does a Genie torsion spring last? A standard spring is rated for roughly 10,000 cycles, and in Sunrise Manor’s dry desert heat that can shorten noticeably; the constant dry air wears on the metal, so we often see them fail closer to the 7,000-to-9,000-cycle mark. If your door cycles four times a day, that’s a few years before you should expect a failure. Call (888) 274-8795 for an exact cycle count on yours.

Can a broken torsion spring be repaired instead of replaced? No. Once the coil breaks, the spring is done; there’s no safe way to weld or patch it back into service, and any shop that offers that isn’t doing you a favor. Replacement with a properly sized spring is the only real fix. Call (888) 274-8795 for a quote.

How long does the swap take? A single-spring replacement is usually a 45-minute to 90-minute job once we’re on site, and most Sunrise Manor calls are handled the same day. The job itself is fast because the fit matters more than the time. Call (888) 274-8795 and we’ll give you a window.

How do you source the Genie-compatible spring? We spec it by measuring your door’s weight, height, and the old spring’s wire gauge and inside diameter, then match to a quality torsion spring that meets or exceeds Genie’s original spec. We don’t guess and we don’t put on a “close enough” spring. Call (888) 274-8795 for a free estimate.

Do you stock Genie springs on the truck? We don’t carry a parts inventory on a truck; we bring the correct spring to your door based on the measurements we take, which is why we measure first and install once. That’s also why we can hold the price we quote: we’re not swapping in whatever happens to be on hand. Call (888) 274-8795 for a free estimate.

Written by the team at Otto’s Garage Door Sunrise Manor, serving Sunrise Manor and nearby areas.

Need Garage Door help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (888) 274-8795
Local Service Coverage

Request a Free Estimate in Sunrise Manor

Tell us what you need - Otto's Garage Door Sunrise Manor responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch